View MB15C101_145112.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

FUJITSU SEMICONDUCTOR DATA SHEET
DS04-21215-3E
ASSP
IF Band PLL Frequency Synthesizer
MB15C101
s DESCRIPTION
The Fujitsu MB15C101 is an exclusive Intermediate Frequency (IF) band Phase Locked Loop (PLL) frequency synthesizer with pulse swallow operation. The reference divider and comparison divider have fixed divide ratios, so that it is not required to set the divide ratios by a microcontroller externally. It operates with a supply voltage of 3.0 V typ. and dissipates 1.0 mA typ.(270MHz) of current realized through the use of Fujitsu's CMOS technology. The MB15C101 is ideally suitable for PHS systems.
s FEATURES
* Low power supply current: ICC = 1.0 mA typ. (VCC = 3 V, 270MHz) * Pulse swallow function; Prescaler: 16/17 * Setting frequency (Selectable by Div input.) - fosc = 19.2 MHz, fIF = 233.15 MHz (Div = "H") - fosc = 19.2 MHz, fIF = 259.20 MHz (Div = "L") * Lock detector * Low power supply voltage: VCC = 2.4 V min. * Wide operating temperature: Ta = -40 to +85C
s PACKAGE
8-pin plastic SSOP 16-pad plastic BCC
(FPT-8P-M03)
(LCC-16P-M06)
1
MB15C101
s PIN ASSIGNMENT
(TOP VIEW)
N.C. N.C. 15 14 13 12 11 10 9 N.C. fin GND DO VCC N.C.
(TOP VIEW)
VCC DO GND fin 1 2 3 4 8 7 6 5 OSC IN LD fout DIV LD 4 5 6 N.C. DIV fout 1 2 3
16
(FPT-8P-M03)
OSCin N.C.
7 N.C.
8 N.C.
(LCC-16P-M06)
s PIN DESCRIPTIONS
Pin No. SSOP8 - 1 2 3 4 5 6 7 8 BCC16 1,6,7,8, 9,14, 15,16 10 11 12 13 2 3 4 5 Pin name I/O Descriptions
N.C VCC DO GND fin Div fout LD OSCin
- - O - I I O O I
No connection Power supply voltage input (2.4 V to 3.6 V). Charge pump output Ground Prescaler input. Connection should be with AC coupling. Divide ratio switching input. Two kinds of divide ratios are selectable by Div input "H" or "L". Test purpose output. This pin is an open drain output so that should be left open usually. Lock detector output. LD = H ; Lock LD = L ; Unlock Reference counter input. Connection should be with AC coupling.
2
MB15C101
s BLOCK DIAGRAM
VCC
Reference divider OSCIN Oscillator input buffer fr Reference counter (R) Phase comparator fp Lock detector LD charge pump
Do
DIV
Data setting circuit
Comparison divider Output selector Swallow counter (A) Main counter (N) fout
fin
Prescaler 16 / 17(P) Control circuit
GND
3
MB15C101
s ABSOLUTE MAXIMUM RATINGS
Parameter Power supply voltage Input voltage Output voltage Output current Storage temperature Symbol VCC VI VOUT IOUT TSTG Rating Min. -0.5 -0.5 -0.5 0 -55 Max. +4.0 VCC +0.5 VCC +0.5 +5 +125 Unit V V V mA C
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
s RECOMMENDED OPERATING CONDITIONS
Parameter Power supply voltage Input voltage Operating temperature Symbol VCC VIN Ta Value Min. 2.4 GND -40 Typ. 3.0 - - Max. 3.6 VCC +85 Unit V V C Note
Handling Precautions * This device should be transported and stored in anti-static containers. * This is a static-sensitive device; take proper anti-ESD precautions. Ensure that personnel and equipment are properly grounded. Cover workbenches with grounded conductive mats. * Always turn the power supply off before inserting or removing the device from its socket. * Protect leads with a conductive sheet when handling or transporting PC boards with devices.
4
MB15C101
s ELECTRICAL CHARACTERISTICS
Recommended operating conditions unless otherwise noted.
Parameter Power supply current fin Operating frequency OSCIN fin Input sensitivity OSCIN
Symbol ICC fin fosc Pfin Vosc VIH
Condition PLL is locked.(270MHz) VCC = 3.0 V, Ta = +25C AC coupling by 1000 pF capacitor AC coupling by 1000 pF capacitor AC coupling by 1000 pF capacitor AC coupling by 1000 pF capacitor - - - - - VCC = 3.0 V, IOH=-0.3mA VCC = 3.0 V, IOL= 0.3mA VCC = 3.0 V, VOH = 2V, Ta = +25C VCC = 3.0 V, VOL = 1V, Ta = +25C 0 VDO VCC
Value Min. 0.1 50 3 -10 0.5 VCC x 0.7 - - -1.0 -100 2.6 - - - - Typ. 1.0 - - - - - - - - - - - -6.0 6.0 - Max. 2.0 270 26 +2 - - VCC x 0.3 1.0 - 100 - 0.4 - - 3
Unit mA MHz MHz dBm Vpp V V A A A V V mA mA nA
Input voltage
Div VIL
Input current Input current Output voltage
Div OSCIN Do
IIH IIL IOSC VOH VOL IOH
Output current
Do IOL
High impedance cut off current
Do
IOFF
5
MB15C101
s FUNCTIONAL DESCRIPTIONS
Two different frequencies can be selected by Div input "H" or "L". The divide ratios are calculated using the following equation: fVCO = {(P x N) + A} x fOSC / R Symbol fvco fosc N A P R (A < N) Div = "H" 233.15 MHz 19.2 MHz 291 7 16/17 384 (fr = 50 kHz) Div = "L" 259.20 MHz 19.2 MHz 33 12 16/17 40 (fr = 480 kHz)
Description Output frequency of external VCO Reference oscillation frequency Divide ratio of the main counter Divide ratio of the swallow counter Preset divide ratio of dual modulus prescaler Divide ratio of the reference counter
s PHASE DETECTOR TIME CHART
fr
fp
tWU
tWL
LD
DO
High impedance
Note: * Phase error detection range: -2 to +2 * Pulses on Do output signal during locked state are output to prevent dead zone. * LD output becomes low when phase is tWU or more. LD output becomes high when phase error is tWL or less and continues to be so for three cycles or more. * tWU and tWL depend on OSCin input frequency. tWU > 8/fosc (s) (e. g.tWU > 625.0ns, foscin = 12.8 MHz) tWL < 16/fosc (s) (e. g. tWL < 1250.0ns, foscin = 12.8 MHz)
6
MB15C101
s MEASURMENT CIRCUIT (for measuring input sensitivity fin/OSCin)
SSOP-8
VCC 1000 pF 1 0.1 F 2 7 2 K 3 S.G 4 1000 pF 50 5 DIV : H or L 6 Oscilloscope 8 VCC 50 S.G
BCC-16
8 9 VCC 1000 pF 10 0.1 F 11 4 2 K 12 S.G 13 1000 pF 50 14 15 16 1 2 DIV : H or L 3 Oscilloscope 5 VCC 50 S.G 7 6
7
MB15C101
s TYPICAL CHARACTERISTICS
1. fin Input Sensitivity
(dBm) 10 5 0 -5 -10
Pfin (dBm)
-15 -20 -25 -30 -35 -40 -45 -50
,
SPEC 100 200 300 SPEC
Ta = +25 C
VCC = 2.4 V VCC = 3.0 V VCC = 3.6 V
0
400
500
fin (MHz)
600
700
800
900
1000 (MHz)
2. OSCIN Input Sensitivity
(dBm) 10 5 0 -5 -10
Vosc (dBm)
-15 -20 -25 -30 -35 -40 -45 -50

10 20 30 40 50
fosc (MHz)
Ta = +25 C VCC = 2.4 V VCC = 3.0 V VCC = 3.6 V
0
60
70
80
90
100 (MHz)
8
MB15C101
3. fin Input Impedance
4 : 11.867 -131.54 4.0331 pF 300.000 000 MHz 1 : 58.875 -850.16 k 50 MHz 2 : 16.891 -416.2 100 MHz 3 : 12.047 -202.87 200 MHz 1 2 4
3
START .500 000 MHz
STOP 1 000.000 000 MHz
4. OSCIN Input Impedance
4 : 068.25 -1.4236 4.3 pF
26.000 000 MHz 1 : 5.1345 -10.288 k 3 MHz 2 : 529.87 -3.6659 k 10 MHz 3 : 114.44 -1.8514 k 4 20 MHz 1 2 3
START .500 000 MHz
STOP 100.000 000 MHz
9
MB15C101
5. Do Outut Current VOH - IOH
3.0 2.5 2.0 VOH (V) 1.5 1.0 0.5 0.0 0 -2 -4 -6 IOH (mA) -8 -10 -12 VCC = 3.0 V, Ta =+ 25 C
VOL - IOL
VCC = 3.0 V, Ta = +25 C 3.0 2.5 2.0 VOL (V) 1.5 1.0 0.5 0.0 0 2 4 6 IOL (mA) 8 10 12
Measurement Circuit
VCC VCC Do GND IOH Parameter Analyzer
fin OSCin S.G. 50 1000 pF
VCC VCC Do GND IOL Parameter Analyzer
fin S.G. 50 1000 pF OSCin
10
MB15C101
s REFERENCE INFORMATION
1. Application Measurement * Test Results Results Lockup time 1 kHz Un lock Lock Power on Lock Reference leakage (f = 58 kHz) Phase noise (f = 1 kHz) (f = 10 kHz) (f = 100 kHz) (f = 1 MHz) 2.3 ms 3.4 ms -88.5 dBc -88.0 dBc/Hz -111.0 dBc/Hz -118.0 dBc/Hz -134.0 dBc/Hz 3.0 V Discrete VCO (Kv = 3.5 MHz/V) Lock Frequency = 274.0 MHz (fr = 58 kHz)
VCC (V) VCO * Measurement Circuit
18 VCC = 3.0 V Loop Filter fin R1 MB15C101 S.G 1000 pF OSCin C1 R2 C3 VCO
18 Spectrum Analyzer
18
1000 pF
50
C2
C1 = 6800 pF C2 = 0.068 F C3 = 4800 pF R1 = 3.0 k R2 = 3.9 K
11
MB15C101
2. Phase Noise
f = 1 kHz ATTEN 10dB SPAN 2.0 kHz RL -1.5 dBm 10 dB/
MKR -73.83 dB 1.000 kHz
f = 10 kHz ATTEN 10dB SPAN 20 kHz RL -1.5 dBm 10 dB/
MKR -91.83 dB 10.00 kHz
D
D
CENTER 273.999827 MHz RBW 30 Hz VBW 3.0 Hz f = 100 kHz ATTEN 10 dB SPAN 200 kHz RL -1.5 dBm 10 dB/
SPAN 2.000 kHz SWP 3.00 sec
CENTER 273.999827 MHz RBW 100 Hz VBW 30 Hz f = 1 MHz ATTEN 10dB SPAN 2 MHz RL -30.0 dBm 10 dB/
SPAN 20.00 kHz SWP 30. 0 sec
MKR -88.50 dB 58.0 kHz
MKR -105.5 dB 275.000 MHz
D
D
CENTER 274.0002 MHz RBW 1.0 kHz VBW 30 Hz
SPAN 200.0 kHz SWP 30.0 sec
START 274.000 MHz RBW 1.0 Hz VBW 100 Hz
STOP 276.000 MHz SWP 100 sec
12
MB15C101
3. Lockup Time: Un-Lock to Lock Un-Lock to Lock : DIV = "L" to "H"
Mkr : 2.30 ms Mkr : 3.40 ms
VCC "OFF" to VCC "ON"
30.00300 MHz
30.00300 MHz
1.00 kHz/div
1.000 kHz/div
29.99800 MHz 0s 20.0000000 ms
29.99800 MHz 0s 10.0000000 ms
13
MB15C101
s ORDERING INFORMATION
Part number MB15C101PFV MB15C101PV1 Package 8-pin, Plastic SSOP (FPT-8P-M03) 16-pad, Plastic BCC (LCC-16P-M06) Remarks
14
MB15C101
s PACKAGE DIMENSIONS
8-pin plastic SSOP (FPT-8P-M03)
* 3.500.10
(.138.004)
*: This dimension does not include resin protrusion.
1.25 -0.10 +.008 .049 -.004
+0.20
(Mounting height)
0.10(.004)
INDEX
4.200.10 (.165.004)
5.20(.205) NOM
6.200.20 (.244.008)
"A"
0.80(.0315) TYP
0.350.10 (.014.004)
0.10(.004)
M
0.15 -0.02 +.002 .006 -.001
+0.05
Details of "A" part 0.100.10(.004.004) (STAND OFF)
2.40(.094)REF
0
10
0.500.20 (.020.008)
C
1994 FUJITSU LIMITED F08005S-1C-2
Dimensions in mm (inches)
(Continued)
15
MB15C101
(Continued)
16-pad plastic BCC (LCC-16P-M06)
4.550.10 (.179.004)
14 9
0.80(.031)MAX Mounting height 0.400.10 (.016.004) 0.80(.031) REF 0.65(.026) TYP
9
3.40(.134)TYP 0.3250.10 (.013.004)
14
INDEX AREA 3.400.10 (.134.004) 2.45(.096) TYP "A" "B" 1.15(.045) REF
1
6
0.0750.025 (.003.001) (Stand off)
6
1.725(.068) REF
1
Details of "A" part 0.750.10 (.030.004) 0.05(.002)
Details of "B" part 0.600.10 (.024.004)
0.400.10 (.016.004)
0.600.10 (.024.004)
C
1999 FUJITSU LIMITED C16017S-1C-1
Dimensions in mm (inches)
16
MB15C101
FUJITSU LIMITED
For further information please contact:
Japan FUJITSU LIMITED Corporate Global Business Support Division Electronic Devices KAWASAKI PLANT, 4-1-1, Kamikodanaka Nakahara-ku, Kawasaki-shi Kanagawa 211-8588, Japan Tel: 81(44) 754-3763 Fax: 81(44) 754-3329
All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document are presented as examples of semiconductor device applications, and are not intended to be incorporated in devices for actual use. Also, FUJITSU is unable to assume responsibility for infringement of any patent rights or other rights of third parties arising from the use of this information or circuit diagrams. FUJITSU semiconductor devices are intended for use in standard applications (computers, office automation and other office equipment, industrial, communications, and measurement equipment, personal or household devices, etc.). CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.) are requested to consult with FUJITSU sales representatives before such use. The company will not be responsible for damages arising from such use without prior approval. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan.
http://www.fujitsu.co.jp/
North and South America FUJITSU MICROELECTRONICS, INC. Semiconductor Division 3545 North First Street San Jose, CA 95134-1804, USA Tel: (408) 922-9000 Fax: (408) 922-9179 Customer Response Center Mon. - Fri.: 7 am - 5 pm (PST) Tel: (800) 866-8608 Fax: (408) 922-9179
http://www.fujitsumicro.com/
Europe FUJITSU MIKROELEKTRONIK GmbH Am Siebenstein 6-10 D-63303 Dreieich-Buchschlag Germany Tel: (06103) 690-0 Fax: (06103) 690-122
http://www.fujitsu-ede.com/
Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE LTD #05-08, 151 Lorong Chuan New Tech Park Singapore 556741 Tel: (65) 281-0770 Fax: (65) 281-0220
http://www.fmap.com.sg/
F9904 (c) FUJITSU LIMITED Printed in Japan
17

▲Up To Search▲

Price & Availability of MB15C101

	To Download MB15C101 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .